• Air Coolers (Rev. 10) – (updated) Improved estimating formulas.
• Asbestos Abatement (Rev. 9) – (updated) Improved estimating formulas.
• Blind Installation (Rev. 12) – (updated) Improved estimating formulas.
• Block Valves – Bolted (Rev. 25) – (updated) Improved schedule logic.
• Butterfly Valves (Rev. 11) – (updated) Includes some enhancements to estimating formulas and allows for the specification of different types of insulation.
• Chain Operators (Rev. 5) – (updated) Improved schedule logic.
• Check Valves (Rev. 7) – (updated) Improved schedule logic.
• Control Valves (Rev. 18) – (updated) Improved estimating formulas.
• Cooling Tower Gear Boxes – Fans (Rev. 4) – (updated) Improved task logic flow.
• Crude Furnace (Rev. 7) – (updated) Improved estimating formula and schedule logic.
• Deaerator (Rev. 7) – (updated) Improved estimating formulas.
• Drum Demolition (Rev. 4) – (updated) A major revision, incorporating many different scenarios involving different types of insulation removal, vessel safing, and rigging options.
• Drum Erection – New (Rev. 5) – (updated) Improved estimating formulas and schedule logic.
• Drums (Rev. 19) – (updated) Improved estimating formulas and also now includes an option to blank off flanges with Strahman/Onis type inline blanking devices that require only one operator and 3 minutes to blind off any line.
• Electronic Transmitters – Field Service – (new) Developed with the assistance of Mr. Greg Dennison, with the DuPont Sabine River Works.
• Flanges – BM (Rev. 9) – (updated) Improved schedule logic.
• Flanges – PF (Rev. 9) – (updated) Improved schedule logic.
• Flare – In Situ (Rev. 5) – (updated) Improved task detail and now includes option to replace thermocouple(s).
• Flare – Shop Repairs (Rev. 3) – (updated) Improved definition for blinding tasks.
• Foundation – Concrete (Rev. 12) – (updated) Improved schedule logic.
• Four Stage Piston Compressor (Rev. 1) – (updated) Added tasks for valve removal and transport.
• Furnace – Open and Close (Rev. 6) – (updated) Improved schedule logic.
• Heat Exchanger Bundle Retubing (Rev. 3) – (updated) Improved estimating formulas and schedule logic.
• Install Conduit and Pull Cable 2in. and Higher (Rev. 1) – (updated) Now includes tasks for installation of underground conduit.
• Install Conduit and Pull Cable Up To 1.5in.(Rev. 1) – (updated) Now includes tasks for installation of underground conduit.
• Motor Operated Valves (M.O.V.s) (Rev. 13) – (updated) Improved estimating formulas and now allows for the tasks involved in asbestos abatement.
• Pipe – Shop Fabrication (Rev. 9) – (updated) Improved estimating formulas.
• Pipe – Small Diameter Welded – Field Erection (Rev. 3) – (updated) Improved schedule logic.
• Pumps – Centrifugal (Rev. 14) – (updated) Improved detail for pump reassembly and now incorporates additional options for three types of insulation removal and installation.
• Rotary Screw Compressor – (new) Allows for the preparation of estimates / plans to open, disassemble, clean and inspect rotary screw type compressors.
• Tanks (Rev. 14) – (updated) Improved estimating formulas and now incorporates tasks and estimates for repairing a tank by installing a vinyl liner and concrete layer over a damaged/leaky floor.
• Unit Blinds (Rev. 2) – (updated) Improved estimating formulas.

eTaskMaker clients may now download the updates from our downloads repository.

eTaskMaker clients may now download the update from our downloads repository. Clients with an Enterprise license should contact InterPlan Systems for customized updates.

• Block Valves – Bolted (Rev. 24) – (updated) Includes some enhancements to estimating formulas and schedule logic. Also incorporates a safety permit and allows for the specification of different types of insulation.
• Block Valves – Welded (Rev. 23) – (updated) Incorporates a safety permit and allows for the specification of different types of insulation.
• Check Valves (Rev. 5) – (updated) Includes some enhancements to estimating formulas and schedule logic. Also incorporates a safety permit and allows for the specification of different types of insulation. Improvements were introduced with assistance of Mr. Joe Hossack, Suncor Energy.
• Heat Exchangers – Fixed Tubesheet (Rev. 15) – (updated) Minor improvements with the bolt inspection tasks.
• Heat Exchangers – Floating Heads (Rev. 16) – (updated) Minor improvements with the bolt inspection tasks.
• Heat Exchangers – U-Tubes (Rev. 26) – (updated) Minor improvements with the bolt inspection tasks.
• Heat Exchangers – Vertical (Rev. 15) – (updated) Minor improvements with the bolt inspection tasks.
• Pipe – Small Diameter Welded – Field Erection (Rev. 2) – (updated) Improved estimating formulas and schedule logic.
• Unit Blinds (Rev. 1) – (updated) Improved estimating formulas and schedule logic.

eTaskMaker clients may now download the updates from our downloads repository.

eTaskMaker clients may now download the update from our downloads repository. Clients with an Enterprise license should contact InterPlan Systems for customized updates.

• Control Valve (Rev. 15) – (updated) Updates some task descriptions and includes a new task for stroking the valve.
• Electric Motor Overhaul (Rev. 7) – (updated) Allows for specifying the level of difficulty in removing an electric motor for shop repairs.
• Expansion Joint (Rev. 4) – (updated) Allows for specifying the refractory cure time (depending upon the type of refractory used).
• F.C.C. Regenerator Flue Gas Line Repairs (Rev. 4) – (updated) Improved estimating formulas.
• F.C.C. Trickle Valves (Rev. 4) – (updated) Allows to specify the number of trickle valves to be inspected/repaired.
• HP Steam Superheater – (new) Includes cleaning out, inspecting and repairing refractory in a HP Steam Superheater.
• Pipe – Field Erection (Rev. 16) – (updated) Allows for the installation of both block and/or control valves, and improves tasks definitions.
• Piping Demolition (Above Ground) (Rev. 3) – (updated) Improved estimating formulas.
• Pumps – Centrifugal – Shop Repairs (Rev. 11) – (updated) Allows for specifying the level of difficulty in removing a centrifugal pump for shop repairs, and improves the task definitions.
• Refractory Repairs (Rev. 4) – (updated) Improved task definition.
• Refrig Compressor Turbine Press Case Overhaul – (new) Covers disassembly, cleaning, inspection and reassembly of a compressor driven turbine pressure case.

eTaskMaker clients may now download the updates from our downloads repository.

The webinar will demonstrate a practical way to produce consistent, reliable estimates for shutdowns/turnarounds/outages in the process industries. Estimates can be exported to most popular scheduling and CMMS applications.

The webinar lasta 45 minutes. To participate, contact us to obtain the GoToMeeting session number. The webinar is limited to 45 participants, so we urge early registration.

The event will be held at:

The Silverado Smokehouse
4522 Weber Road
Corpus Christi, TX
(361) 855-6464

Lunch is dutch treat, but there is no cost for the presentation. This event is open to everybody, and no reservations are necessary. We hope to see you there.

• Four Stage Piston Compressor – (new) Replaces the basic compressor module originally included with eTaskMaker. This one has much better definition.
• P.M. Breakers – (new) This module was created in collaboration with Mr. Steve Clark of DuPont – Sabine River Works.
• P.M. Disconnects – (new) This module was created in collaboration with Mr. Steve Clark of DuPont – Sabine River Works.
• Piping – Rubber Lined – Pinhole Leak Repair – (new) Allows for the preparation of an estimate / plan to remove a rubber lined piping spool for cleaning, inspection and repair.
• Rotary Screw Compressor – (new) Allows for the preparation of estimates / plans to open, disassemble, clean and inspect rotary screw type compressors.
• Scrubbers – (new) Allows for the preparation of estimates / plans for three different types of scrubbers (Eductor, Impinjet, Venturi).

In addition, the following existing modules were enhanced to allow the insertaing of I.D. Tag Numbers into tasks, and to allow the preparation of estimates from a list of like items:

• Block Valves – Bolted (Rev. 23)
• Block Valves – Welded (Rev. 21)
• Butterfly Valves (Rev. 8)
• Check Valves (Rev. 4)
• Control Valves (Rev. 14)
• Electric Motor Overhaul (Rev. 5)
• Flow Transmitters (Rev. 1)
• Level Controllers (Rev. 6)
• Level Glass Assembly (Rev. 6)
• Level Transmitters (Rev. 3)
• Limit Switches (Rev. 1)
• Pipe – Field Erection (Rev. 15)
• Push Buttons (Rev. 3)
• Safety Valves (Rev. 7)
• Slide Valves (Rev. 5)
• Solenoid Valves (Rev. 7)
• Speed Tachometers (Rev. 1)
• Thermowells (Rev. 4)

In addition to that, the following existing modules were updated:

• Check Valves (Rev. 4) – (updated) Improved flow chart definition.
• NH3 Process Compressor (Rev. 6) – (updated) Edited some task descriptions to avoid truncation issues.
• Pipe – Field Erection (Rev. 15) – (updated) Improved some of the estimating formulas.
• Pipe – Shop Fabrication (Rev. 8) – (updated) Improved some of the estimating formulas.

Finally, numerous modules – too many to list here – were updated to remove adjustable resource productivity factors as eTaskMaker now has a built in method for controlling these norms. There are so many new and updated modules in this update release that we have included a .ZIP archive named modules.zip in the main folder of the downloads repository that contains the latest version of every module in our inventory.

eTaskMaker clients may now download the updates from our downloads repository.

eTaskMaker clients may now download the update from our downloads repository. Clients with an Enterprise license should contact InterPlan Systems for customized updates.

eTaskMaker clients may now download the update from our downloads repository. Clients with an Enterprise license should contact InterPlan Systems for customized updates.

The eTaskMaker demo has also been updated with the latest version of the Wizard.