eTaskMaker Module Updates for March

InterPlan Systems has released the following updated eTaskMaker estimating modules:

• Air Coolers (Rev. 10) – (updated) Improved estimating formulas.
• Asbestos Abatement (Rev. 9) – (updated) Improved estimating formulas.
• Blind Installation (Rev. 12) – (updated) Improved estimating formulas.
• Block Valves – Bolted (Rev. 25) – (updated) Improved schedule logic.
• Butterfly Valves (Rev. 11) – (updated) Includes some enhancements to estimating formulas and allows for the specification of different types of insulation.
• Chain Operators (Rev. 5) – (updated) Improved schedule logic.
• Check Valves (Rev. 7) – (updated) Improved schedule logic.
• Control Valves (Rev. 18) – (updated) Improved estimating formulas.
• Cooling Tower Gear Boxes – Fans (Rev. 4) – (updated) Improved task logic flow.
• Crude Furnace (Rev. 7) – (updated) Improved estimating formula and schedule logic.
• Deaerator (Rev. 7) – (updated) Improved estimating formulas.
• Drum Demolition (Rev. 4) – (updated) A major revision, incorporating many different scenarios involving different types of insulation removal, vessel safing, and rigging options.
• Drum Erection – New (Rev. 5) – (updated) Improved estimating formulas and schedule logic.
• Drums (Rev. 19) – (updated) Improved estimating formulas and also now includes an option to blank off flanges with Strahman/Onis type inline blanking devices that require only one operator and 3 minutes to blind off any line.
• Electronic Transmitters – Field Service – (new) Developed with the assistance of Mr. Greg Dennison, with the DuPont Sabine River Works.
• Flanges – BM (Rev. 9) – (updated) Improved schedule logic.
• Flanges – PF (Rev. 9) – (updated) Improved schedule logic.
• Flare – In Situ (Rev. 5) – (updated) Improved task detail and now includes option to replace thermocouple(s).
• Flare – Shop Repairs (Rev. 3) – (updated) Improved definition for blinding tasks.
• Foundation – Concrete (Rev. 12) – (updated) Improved schedule logic.
• Four Stage Piston Compressor (Rev. 1) – (updated) Added tasks for valve removal and transport.
• Furnace – Open and Close (Rev. 6) – (updated) Improved schedule logic.
• Heat Exchanger Bundle Retubing (Rev. 3) – (updated) Improved estimating formulas and schedule logic.
• Install Conduit and Pull Cable 2in. and Higher (Rev. 1) – (updated) Now includes tasks for installation of underground conduit.
• Install Conduit and Pull Cable Up To 1.5in.(Rev. 1) – (updated) Now includes tasks for installation of underground conduit.
• Motor Operated Valves (M.O.V.s) (Rev. 13) – (updated) Improved estimating formulas and now allows for the tasks involved in asbestos abatement.
• Pipe – Shop Fabrication (Rev. 9) – (updated) Improved estimating formulas.
• Pipe – Small Diameter Welded – Field Erection (Rev. 3) – (updated) Improved schedule logic.
• Pumps – Centrifugal (Rev. 14) – (updated) Improved detail for pump reassembly and now incorporates additional options for three types of insulation removal and installation.
• Rotary Screw Compressor – (new) Allows for the preparation of estimates / plans to open, disassemble, clean and inspect rotary screw type compressors.
• Tanks (Rev. 14) – (updated) Improved estimating formulas and now incorporates tasks and estimates for repairing a tank by installing a vinyl liner and concrete layer over a damaged/leaky floor.
• Unit Blinds (Rev. 2) – (updated) Improved estimating formulas.

eTaskMaker clients may now download the updates from our downloads repository.